CanFly

3.5" programable multi function display

A capable 3.5" display with a super bright 320 x 240 pixel display. Running the Kotuku CanFly® operating system with the diy-efis application installed.
Features:
  • Designed to fit into a standard 3" instrument hole
  • Graphics processing engine for hardware drawing.
  • Comes configured with a PFD or EFI application. Others can be downloaded from the diy-efis site.
  • Rotary knob and cancel button for use with diy-efis applications.

Engine data features

When combined with a Kotuku kEDU the following features are available.
  • Engine Manifold Pressure
  • Engine RPM
  • Oil Pressure
  • Oil Temperature
  • Outside Air Temperature
  • Fuel Pressure
  • Fuel Flow
  • Volts
  • Amps
  • Exhaust Gas Temperature
  • Cylinder Head Temperature
  • Fuel Flow
  • Total Fuel
  • Alarm display
  • % HP
When combined with a kECU Electronic ignition the following features are also added to the engine display.
  • MAP from both systems are averaged and displayed
  • RPM from both EFI systems are averaged and displayed
  • kECU status (left/right)
  • Mixture mode (auto/manual)
  • Timing divergence alarm
  • Injector fail alarm
  • Ignitor fail alarm
  • Auto-lean status

Primary Flight Display features

Avionics
When combined with a kotuku kHUB attitude system the following features are available.
  • Attitude (Pitch/Role/Yaw)
  • Magnetic heading
  • Airspeed including v speed markers
  • Altitude
  • Veritical speed
  • GPS track
  • Autopilot status
  • Next waypoint
  • Time to next
  • Distance to next
  • Course marker
  • Current comm frequency
  • Backup comm frequency
The comm and GPS functions require a compatible comm tranceiver (SL40) and ADSB transponder
Kotuku recommends the Trig ADSB transponder and comms tranceiver
The engine probes for the selected engine must be also purchased.
Due to the world-wide electronics shortages there may be up to an 8-week delay on shipments. Please email support@kotuku.aero to get an estimated delivery

EGT Probe

Transducer
Alcor K-Type EGT probe
  • Backed by an industry leading 5-year warranty
  • Small element diameter provides for near instantaneous instrument response
  • Built in radiator minimizes the high temperature effects on internal spotweld connections
  • Clamp fits 1 1/8″ to 3 3/8″ diameter exhaust systems with approximately .1285″ size hole
  • Accurate to ± 25 degrees at 1500 degrees Fahrenheit
  • Comes with 5ft of K wire and terminals ready to install on kEDU

CHT Probe

Transducer
K-Type thermal well CHT probe
  • Backed by an industry leading 5-year warranty
  • Small element diameter provides for near instantaneous instrument response
  • Lead wires are configured in reverse stagger(long red and short yellow)
  • Alcor probes are designed, manufactured, and supported in the U.S.A.
  • Includes the Thermo-well adapter
  • Include 5ft of type K cable with pins

100 Psi Oil pressure transducer

Transducer
Oil pressure gauge for EDU. Comes complete with 5ft terminated cable. Extra pins provided to shorted cable if needed.

Current Shunt

Transducer
Current shunt for +/- 40A. Must be mounted to a bulkhead with thermal compound (Supplied). Comes with 5ft cable and connector pins.

CanFly termination cover

collapsible
Used for the end of a canfly cable. Contains a 45 degree cover, 120 ohm termination resistor and 9 pin female connector.

4 Cyl EFI for O-320 complete with type 4 flange and 4 injectors

kECUKit FuelBlock ThrottleBody
Complete EFI system with a type 4 updraft intake flange.
  • Dual kECU Generator, Ignition and Injection controllers with manual mixture control
  • CanFly bus connector for data feed and programming
  • 4 Injector channels
  • 4 Cylinider Ignition
  • Dual Manifold pressure sensors
  • Dual Manifold temperature sensors
  • Each generator senses internal voltage
  • Ignition harness
  • 8 x 14mm spark adapters
  • Fuel distribution block with fuel pressure sensors
  • Type 4 flange up-draft throttle body
  • 4 dual-fire fuel injectors
  • Programming adapter.
  • This is for experimental aircraft use only. Extra cables and fittings may be required to be provided by the builder.
The Lycoming engine must have a fuel injection fuel pump, as well as a 28psi electric fuel pump. These are not provided.
Due to the world-wide electronics shortages there may be up to an 8-week delay on shipments. Please email support@kotuku.aero to get an estimated delivery

4 Cyl EFI for O-360 complete with type 5 flange and 4 injectors

kECUKit FuelBlock ThrottleBody
Complete EFI system with a type 4 updraft intake flange.
  • Dual kECU Generator, Ignition and Injection controllers with manual mixture control
  • CanFly bus connector for data feed and programming
  • 4 Injector channels
  • 4 Cylinider Ignition
  • Dual Manifold pressure sensors
  • Dual Manifold temperature sensors
  • Each generator senses internal voltage
  • Ignition harness
  • 8 x 14mm spark adapters
  • Fuel distribution block with fuel pressure sensors
  • Type 4 flange up-draft throttle body
  • 4 dual-fire fuel injectors
  • Programming adapter.
  • This is for experimental aircraft use only. Extra cables and fittings may be required to be provided by the builder.
The Lycoming engine must have a fuel injection fuel pump, as well as a 28psi electric fuel pump. These are not provided.
Due to the world-wide electronics shortages there may be up to an 8-week delay on shipments. Please email support@kotuku.aero to get an estimated delivery

CanFly cable 8"

Transducer
CanFly cable with daisy-chain connector. 200mm (8") of free cable. Terminated on one end with a connector. Other end ready to plug into next connector.

CanFly cable 12"

Transducer
CanFly cable with daisy-chain connector. 300mm (12") of free cable. Terminated on one end with a connector. Other end ready to plug into next connector.

CanFly cable 12"

Transducer
CanFly cable with daisy-chain connector. 600mm (20") of free cable. Terminated on one end with a connector. Other end ready to plug into next connector.

CanFly cable 20"

Transducer
CanFly cable with daisy-chain connector. 500mm (20") of free cable. Terminated on one end with a connector. Other end ready to plug into next connector.

CanFly cable 24"

Transducer
CanFly cable with daisy-chain connector. 600mm (24") of free cable. Terminated on one end with a connector. Other end ready to plug into next connector.

CanFly cable 36"

Transducer
CanFly cable with daisy-chain connector. 1m (36") of free cable. Terminated on one end with a connector. Other end ready to plug into next connector.